Call Control


Line box layout

Controlling calls in Solo is both intuitive and straightforward. Essential information for each active call is shown in Solo's linebox. A typical example is shown below, along with an indication of which information is being shown where.

Image

Call State

The Call State information tells us what state the call is currently in. In the example above, the call is "Held". It is not routed to a device and the caller would probably be waiting to go on air, whilst hearing the station output on their telephone. Other common states include Ringing (meaning that an inbound or outbound call is yet to be answered), and Connected (meaning that the call is on a device).

Name

Solo has comprehensive databases built into the system. This means that when a call arrives in the system, if it is from a known phone number (using Caller ID) then Solo will present on screen the caller name associated with that number if one is known. If not, the system will display the phone number of the calling entity. If no CLI information is given by the caller then „WITHHELD‟ will be displayed instead. In cases where the caller is not known to the Solo system a name may be entered manually.

Location

In a similar way to the Name information presentation, Solo will also display a Location for the caller if one is known. If one is not known but CLI is present, then Solo will use its look-up database of area codes and will display the nearest locality it can match to the telephone number. Again, Location information can be entered manually.

Point

The Point field is used to provide a brief description of what the caller wants to say so that producers and presenters are aware of each caller's angle before they take the call.

Call Duration Timer

The Call Duration Timer is the total time that the call has been present in the PhoneBOX system. This timer does not reset when the call changes state.

Dialling a Call

The simplest way to dial a call in Solo is as follows:


Image



Answering a Call

A ringing call in Solo will flash blue and yellow on screen as shown below.

Image

In situations where the caller is sending CLI information, the caller's phone number will be displayed. If the caller is already known to the Solo database then the caller's name will be shown in place of the phone number, as shown above.

To answer a ringing call:
Alternatively:

Placing a Call on Hold

To take a call that is already on a device, and place that call on hold, simply click on the LineBox of the line in question. The LineBox will turn light green, as shown below..

Image



Terminating a Call

Should a caller hangup at the remote end then the call will automatically disappear from the Solo screen (you may experience a slight delay if using analogue lines).

If you wish to terminate a call from Solo, do the following:

Dump mode

When Dump Mode is active, active calls will automatically be dropped when a new call is taken on the same device.

Image



Routing a Call

Routing describes the sending of a call that is on hold, and placing it on a device.

To route a call that is holding, simply click on a device to make it active, then click the LineBox for the line you wish to route. Both the LineBox and the active device will then display the same colour, that of the active device.

Image

Other Buttons

Image

Answer Call

This button will answer an incoming call. You can either click the button then click the call, or alternatively drag the button onto the call.

Make Call

This will bring up the dialer. From the dialler you can select from any available standard (aLaw, uLaw), use the "Last 5" button to call up the last 5 numbers dialled, and also simply dial a call.

Dump mode

As described earlier, when Dump Mode is on, active calls will automatically be dropped when a new call is taken on the same device. Dump mode can be toggled on and off using the button on the Telephony Tool Bar.

Drop Call

This button behaves in a similar way to the Answer Call button, but will end a call instead.

Lines

This dropdown allows you to open or close all lines at once.

Editor

Clicking this button will drop down a list of possible recordings to edit. Selecting one of these will open it in the editor.

Tools

The tools button reveals a menu that allows you to control various parts of Solo's configuration, including marking known numbers as banned or assigning warnings, and performing audio tests, aa well as configuring Solo's core settings (via teh Admin menu - please note this will not be available to all users).